How to setup software-LED SHOW-T9 for HC-102 receiving card?

1,How to install and set up software LED SHOW-T9 for HC-102 receiver quickly:
  Note: (Important)
 1,The network card of your computer must be 1000mbps or GIGABIT speed;
 2,Computer display resolution: 1024 by 768

1.Install the LED show; Pls download from:
 https://www.dropbox.com/s/qzndde91fhsj908/LED%20SHOW-T9%20Easy%20controller.rar

2.Open the software: LED show,(open as a administrator if you use Vista,Win7,If you can not install software on win7, pls install the file for win7 from that software link)

3. Click: Control(C)

4.Choose: Screen management(L);

5,Choose: Use net card, choose Gigabit ethernet Nic

6. Click: LED1, -(left corner of window)

7.Click: Config Selected one...

8. Fill in the password: T9; Click: OK, Click: Yes.

9. Click: Load... -(Button which is at the bottom of this window);

10.Load the "FILE FOR T9.DAT" files I supply for you.

11.Click: Send to receiving card; click: OK;

12.Click:Save on receiver.


2,The way to adjust the right size for your curtain:

1.Install the LED show;

2.Open the software: LED show,(open as a administrator if you use Vista,Win7)

3. Click: Control(C)

4.Choose: Screen management(L);

5. Click: LED1 (left corner of window);

6.Click: Config Selected one...

7.Fill in the password: T9; Click: OK, Click: Yes.

8,Click: Connect setting: setup the right size-Height and Wide pixels of your curtain;


9, Click: Send to receiving card

3,How to use the software with Madrix or arkaos Grand VJ.resolume or other third-party player? 

1, Open the software to choose Capture screen model

2, Pls move the Madrix or arkaos software play area to fix the software-T9 after you setup and close it.

Christmas promotion for flexible led screen display,LED video wall,led strip,led dot

Christmas promotion for flexible led screen display,email me at: huasuntech@aol.com

Flexible LED display promotions for Christmas soon!

Flexible LED display promotions for Christmas soon! Email huasuntech@aol.com if you want one of them, thanks!

Flexible LED video curtain screen-18mm,20mm,25mm....100mm

UK Disney Projects with 20mm led video curtain display: (Each panel is 3.2 by 1.28m wide, 6 panels, total size 3.2 by 7.68mwide)

more info www.tecdisplays.com

commercial led displays

How to configure the Software- LINSN LED STUDIO for HC-103 and HC-101 receiving card with LED curtain?

Rental LED display Novastar software setting manual, novastudio,NovaCT

Novastar setting steps:

1, Installation

Firstly please unzip the installation package "NovaLCT V5.2.0.zip", then double-click

"NovaLCT V5.2.0.exe" and follow the installation wizard to complete the software

installation. If the firewall prompt appears, please select to allow the installation.

2, Login in

Step 1: Open NovaLCT and choose User > Advanced Synchronous System User Login.

Step 2: Enter the password for logging in the terminal, and click Login.

The default password is "admin". If the login is successful, the interface below will

appear, as shown in Figure 2-1.

Figure 2-1 Successful login interface

3,  Screen Configuration Using System Configuration Files

The advantage of using system configuration files to configure LED displays is that

the configuration procedure is very simple and easy, and no manual configuration

operation is required.

Step 1: Click on the main interface: Screen Configuration, and the Screen Configuration window pops up as shown in Figure 3-1.

Step 2: Set the Current Operation Communication Port.

l If the control computer is connected to the synchronous system with one line,

the communication port that the software defaults to is the current

communication port.

l If the control computer is connected to multiple synchronous systems with

different lines, please choose the corresponding communication port of the

synchronous system to be configured.

Step 3: Select the Load Config File option, use the Browse button to select the system

configuration file to be loaded.

Step 4: Click Next. The selected configuration file will be automatically loaded to the LED display system. The LED display system will have been configured when the load

operation is finished.

4, Screen Connection

Select Screen Connection page in the Screen Configuration window (Figure 4-1).

Enter screen number (number of the LED displays to be configured) and click

Configure button, The default screen configuration page (page for standard LED

display configuration) will displayed, as shown in Figure 4-1.

Figure 4-1 Screen connection

  Quantity

This is the number of LED displays that are to be configured.

l Configure

This button is used to load the Screen Number to the NovaLCT application.

l Read form HW

This is used for the application to read the LED display information from the

hardware.

l Detect Communication Status

This is used to check whether the communication within the current LED display

is good.

l Read the Number of Receiving Cards

Get the number of receiving cards loaded by each of the Ethernet ports of the

current sending card.

l Enable Mapping (only supported by some receiving cards of the Armor series)

When this function is opened, current serial number of the cabinet and its

Ethernet port No. will be shown on the cabinet.

l Load from File

Load screen information files save on control computer.

l Save to File

This is used to save screen information files as screen information file (*.scr).

l Send to HW

This is used to send the LED display configuration settings to the connected

sending card.

l Restore Factory Settings

Reset current parameter configuration to factory settings.

l Restore System Configuration

Reset current operating status of the system (or sending card, or receiving card)

to the status in the backup file.

l Back Up System Configuration

Back up current configuration parameters.

l Save System Configuration File

Save system configuration parameters as a file.

l Save This is used to save the settings to a FLASH chip. The saved data won’t be lost even the hardware is powered off.

This all steps.

LINSN CONTROL SYSTEM

How to install and set up LED studio software with LED curtain quickly ?
  --Pls download from: https://www.dropbox.com/s/pvlwwg9jb5ffy1b/NEW-LINSN-LED%20STUDIO%20SETUP.rar
  The software you used must be the newest model.
Note: (Important)
  1,  The VGA card of your computer must be setup to clone or copy model;
   2, Computer display resolution: 1024 by 768

LED studio setup steps: 1. Install the LED studio (serial number:888888);
2.open the soft ware: LED studio
3. click: option
4.choose: software setup;
5. input " linsn" directly(when you see the software setup windows);
6. input password: 168.
7.click: Receiver;
8. click: Load from files;
9. load the "RCG" files I supply for you. Pls email me to get one: huasuntech@aol.com
10.click: Send to receiver; click: OK;
11.click:Save on receiver.

If you use 2 or more receiving card with Led curtain screen, pls follow:

1. Install the LED studio (serial number:888888);
2.open the soft ware: LED studio
3. click: option
4.choose: software setup;
5. input " linsn" directly(when you see the software setup windows);
6. input password: 168.
7.click: Display connection
8. click: Load from files;
9. load the "CON" files I supply for you. CON file size is the size of your curtain pixel or pls find setup photo below:



Or get CON file by yourself, Just setup for a few number according to curtain pixel:

1, horizontal card number: 
2,vertical card number;
3,pixel number of each card; like 2.56 meter for 20mm, pixel number is 128,then put in 128
4.click: Send to receiver; click: OK;
5.click:Save on receiver.

What is the standard size or what size is available,how to calculate the size for Flexible LED display?

1,Question: what is the standard size or what size is available for led curtain, how to calculate the size?
Answer:
1, Any size of LED curtain is available. there is not a standard size which limit you too,only suggested size for each panel.

2,How to calculate the size?
Each pitch size model will have exact size for each module,so you need add or reduce your size according to the module size.
Take 20mm pitch for example, each module size is 0.32m,so your size will be 0.32,0.64,0.96,1.28m.......

Pls check the following chart for your reference for all FLC series:

2,Recommended panel size for each model :(The panel will be connected for a big display or used separately.It is good for packing,transportation and installation.)

18mm, 1.46 by 2.336 wideth meters
20mm:  2.56 by 1.28 wideth meters 
25mm:  2.4 by 1.6 wideth meters 
37.5mm: 3 by 2.4 wideth meters  
50mm: 3.2 by 2.4 wideth meters
75mm: 3.6 by 2.4 wideth meters  
100mm: 3.2 by 3.2m wideth meters  

3,MOQ: The best size for video or image display for each model or for a sample.(These size is for 2 panels connection)

18mm, 1.46 by 2.336 wideth meters  (One panel)

20mm: 2.56 by 2.56 wideth meters   (Two panels)

25mm: 2.4 by 3.2 wideth meters     (Two panels)

37.5mm: 3 by 4.8 wideth meters     (Two panels)

50mm: 3.2 by 4.8 wideth meters     (Two panels)

75mm: 3.6 by 4.8 wideth meters     (Two panels)

100mm: 3.2 by 6.4m wideth meters  (Two panels)